news

Spiral chute image 1: Introduction: The chute sorting includes the inclined flow sorting process. Mineral mortar is fed to a partially inclined chute or inclined surface. Under the driving force of water flow, the mineral particle group is loose and layered, and the lighter minerals in the upper layer quickly flow out of the groove. The heavier minerals in the lower part either stagnate inside the groove or are discharged from the lower part at a low speed. After obtaining the difference, concentrate and tailings are obtained. The fiberglass spiral chute is a machine for mining and beneficiation, especially ideal for sand mining on coasts, riverbanks, sandbanks, and river beds. The equipment has the characteristics of correct structure, simple installation, small land occupation, simple operation, stable beneficiation, clear screening of minerals, large processing capacity, high efficiency, high beneficiation concentration ratio, high recovery probability, and stable operation. There are also advantages such as lightweight, moisture prevention, rust prevention, corrosion resistance, and strong applicability to fluctuations in ore feed volume, concentration, particle size, and grade. 2、 Production principle: The spiral mineral separator is not limited to placing on the cross (or tripod) of the support table. The uniform slurry is slowly fed to the rotating groove surface through the feeding groove installed at the head of the spiral groove for sorting. A valve type product selection slot is installed at the tail, allowing the selection equipment to be divided into three (or four) categories according to grade along the radial direction. Adjust the orientation of the valve block to obtain the width of each device. The product gathering bucket is a concentric circular tube that distinguishes and densely draws out the intercepted multi-directional mineral flow. The transverse surface of the fiberglass spiral chute and the slope change of the curve are particularly suitable for the selection of fine particle materials. Spiral chute image III. The characteristic spiral concentrator has attracted more attention in many gravity beneficiation equipment due to its low power consumption, simple structure, small land occupation, simple operation, stable beneficiation, clear separation of ore, no moving parts, easy maintenance and management, strong single area processing ability, and other characteristics. The machine has a relatively wide and stable trough surface, and the slurry has a large laminar flow area, which is more suitable for processing medium and fine (-4MM) Granularity ores. Spiral chutes with diameters of 400, 600, 900, and 1200 millimeters have been produced in China, Ф The production capacity of 1200mm four head is about 4-6 t/h. Picture 4 of the Spiral Chute: The fiberglass spiral chute is composed of six parts: a feeding homogenizer, a feeding chute, a rotating chute, a product acquisition chute, an equipment gathering hopper, and a support bracket (including a cross or triangular frame). The spiral groove formed by connecting the spiral pieces is a key accessory. The rotating plate is made of fiberglass (fiberglass reinforced coal gangue) and connected together by screws. The rotating groove has a durable wear-resistant layer made in advance on the selected surface. He also has the advantages of lightweight, strong, durable and durable consumables that are not easily damaged. The spiral groove is equipped with a multi tube ore feeding homogenizer to separate minerals, which is easy to operate. The mineral separator does not need to be restricted to placing on a cross (or tripod) on a support table. The evenly divided slurry is slowly fed onto the surface of the spiral groove through the feeding chute at the head of the rotating groove for sorting. The tail of the rotating groove is installed in the valve type new equipment selection groove, and other new equipment is selected to be divided into three (or four) types of new products according to grade along the radial direction. Change the cutting width of each new product by adjusting the position of the valve block. The new product gathering bucket is a concentric circular tube that distinguishes and converges the obtained multi-directional mineral flows. The cross-section of the spiral chute and the slope change of the curve are very suitable for the separation of fine particle materials. Picture 5 of spiral chute: This machine is suitable for separating iron ore, Ilmenite, chromite ore, pyrite, zircon sand, Rutile, monazite, phosphate ore, tungsten ore, tin, tantalum ore, niobium ore and other non-ferrous metals, rare mineral metals or nonferrous metal minerals with different density and specific gravity from small materials with Granularity of 0.3-0.02MM. Spiral Chute Image